Contact Support

This Dongle is required for using a personal computer along with Polara's free PC APP to communicate with an iNS push button station or an iCCU. Your personal computer must have Windows 7 or higher. Download the cutsheet

This Set Up Box is for powering an iNS3, or an iNS2 (as a 3 Wire), and also earlier iN Series (iN3 & iN2 as a 3 Wire) push button stations in 3 Wire Mode so they can be set up or programmed in the shop or at ones desk without being connected to a traffic cabinet or PED head. Download the cutsheet

This Interconnect Board is required for landing of intersection/field button wires when an iCCU-S2 Control Unit is used. Download the cutsheet

This Interconnect Board and Power Supply (purchased separately, PN: iN2-150WPS-C) is required for landing of intersection/field button wires when an iCCU-C2 Control Unit is used. The Power Supply connects to the Interconnect Board and provides the necessary additional power to operate the push button stations. Dowload the cutsheet

This is the same 50 pin cable assembly used with the EZ CCU2EN and is required when the iCCU-S is used without SDLC. It comes in three different cable length options. See EZ Control Unit download section for details. Download the cutsheet

This 2-Cable harness is used to connect an iCCU-S to a traffic cabinet's pedestrian input files, and if needed preemption or general purpose inputs. See Cut sheet for use cases. Download the cutsheet

This cable is a standard 6' long SDLC cable used with the iCCU-S when SDLC is used. Download the cutsheet

This is a custom SDLC cable for use when there are no extra/available SDLC connection points in an intersection traffic cabinet. It allows our Control Units to be able to tap into an existing SDLC connection. Download the cutsheet

This is the power supply used in conjunction with an iCCU-C and iN2-ICB-C. Download the cutsheet

This cable is used to interface the iCCU-C to a 300 series traffic cabinet. Download the cutsheet

This mount is designed to hold a CCU2EN, iCCU-S or iCCU-S2 type control unit and bolt to a rack channel with EIA universal spacing. Download the cutsheet

This adapter is for mounting two iNS iNavigator push button stations on a 2.9" OD pole (2.5" ID) so that they can use 9X12 or 9X15 signs and not touch. It comes in the standard color black. Download the cutsheet

This adapter is designed to offset two iNavigators with 9x12 or 9x15 signs on a 4.5" OD pole. This product is only offered in the color black. Download the cutsheet

This adapter is designed to allow an "iN" or "iNS" Navigator or PBF2C to be mounted directly on, or up to 20 degrees to either side of a flute. This product is only offered in the color black. Download the cutsheet

This mount is designed to facilitate easy routing and connection of ½" diameter conduit to the bottom of the mount, prior to securing an iNS/iDS (or any other Polara model push button with the same form factor), to a wooden pole, or flat concrete or metal surface that does not allow internal wire routing to the button. Download the cutsheet

This pole cap attaches to an iNS iNavigator Push Button Frame and covers the top of a 2.9" OD stub pole used to mount iNavigators close to the start of a crosswalk. Download the cutsheet

This mounting extender is designed to mount an "iN" or "iNS" Navigator, PBF2, or PBF2C either 6" or 12" from a traffic pole in order to extend the unit closer to the crosswalk. Download the cutsheet

This mounting extender is angled down and designed to reduce button mounting height of up to approximately 5". Download the cutsheet

This mounting extender is curved down and designed to reduce/adjust button mounting height of up to 15". Download the cutsheet

This sign back plate is designed to be attached to any iNavigator PBS or any Push Button Frame, for mounting a 9” x 12” crosswalk sign. To designate color in place of X use "B" for black, "G" for green and "Y" for yellow. Download the cutsheet

This sign back plate is designed to be attached to any iNavigator PBS or any Push Button Frame, for mounting a 9” x 15” crosswalk sign. To designate color in place of X use "B" for black, "G" for green and "Y" for yellow. Download the cutsheet

If you need to field replace a R/L arrow button, this assembly is for a bi-direction application.

If you need to field replace a R/L arrow button, this assembly is for a no-arrow application. A typical application is a scramble intersection.

If you need to field replace a R/L arrow button, this assembly is for a bi-direction application.

This color change kit is a bundle of the required parts needed to change the Front Cover color on an iNavigator PBS. To designate color in place of X use "B" for black, "G" for green and "Y" for yellow. Download the cutsheet

This speaker is set up to allow easy field replacement of an iNavigator PBS speaker. Download the cutsheet

This is an external horn style speaker that typically installs on a PED Head for the purpose of providing greater directed volume on large intersections, or beaconing on intersections. This external speaker is connected to a iNS Push Button Station (PBS) with the -ES option.

You can purchase cans of spray paint in the colors that match Polara's black, green and yellow powder coat colors. Part numbers for ordering are as follows: 190-1054 for black, 190-1055 for green, 190-1056 for yellow.

This adapter designed to mount all iNavigator models (iN & INS) & push button station models (PBF2 & PBF2C) to either the right or the left of a mounting extender. reduce/adjust button mounting height of up to 15". Finish is aluminum with black powdercoat. Download the cutsheet

This is the cable that is used to connect the iPHCU3S to the iNS in 3-wire mode or iNS3 (3-wire only unit) iNavigator Push Button Station and comes in a 12, 25 and 50 foot lengths. Part numbers for ordering are iN3-CABLE-12 for 12', iN3-CABLE-25 for 25', iN3-CABLE-50 for 50' Download the cutsheet