iCCU-S2 Shelf Mount Control Unit

Part number:
iCCU-S2
Compatible with:
iDS2, iNS2

The iCCU-S2 is a universal central control unit that can be used in any style traffic cabinet and replaces the iCCU-S. It is backwards compatible with the iCCU-S with just cable changes.

Download the cutsheet

iCCU-C2 Card Rack/300 Series Control Unit

Part number:
iCCU-C2
Compatible with:
iDS2, iNS2

This control unit takes two slots in the detector rack of 300 Series type Traffic Cabinets.

Download the cutsheet

iPHCU3S Ped Head Control Unit 

Part number:
iPHCU3S
Compatible with:
iDS3, iNS3

This control unit mounts in the pedestrian signal head and connects to the iNS by a three-wire cable. Powered by the 120 VAC power to the walk/don’t walk light signals.

Download the cutsheet

Latching Push Button Controller

Part number:
LPBCU2
Compatible with:
BDL3

The LPBCU2 latching push button control unit is a standalone controller designed to provide latching functionality for Polara’s BullDog III (BDL3) pushbuttons. It is designed to mount to the cabinet rails inside a traffic control cabinet in several orientations.

Download the cutsheet

Push Button Control Unit – 120 VAC Version

Part number:
PBCU
Compatible with:
BDL3, BDLM2, BDLL2 

The LED on a standard BDL3 BullDog flashes momentarily each time the button is pushed. If a customer wants the LED on a button to stay on following a push, this Push Button Control Unit controls the LED so it stays on until the pedestrian walk light turns on. It takes up two slots in the detector and is powered by 120 VAC.

Download the cutsheet

iCCU-S2 interconnect board

Part number:
iN2-ICB
Compatible with:
iDS2, iNS2

This interconnect board is required for landing of intersection/field button wires when an iCCU-S2 control unit is used.

Download the cutsheet

iCCU-C2 interconnect board

Part number:
iN2-ICB-C
Compatible with:
iDS2, iNS2

This interconnect board and power supply (purchased separately, PN: iN2-150WPS-C) is required for landing of intersection/field button wires when an iCCU-C2 control unit is used. The power supply connects to the interconnect board and provides the necessary additional power to operate the APS.

Download the cutsheet

iCCU-S2 hardware kit for cable strain relief

Part number:
HK-035
Compatible with:
iDS2, iNS2

Provides strain relief for iCCU-S2 cable(s), or if using 50PINADP adapter cable.

Download the cutsheet

iCCU-S2 50-pin 4-cable harness mating adapter

Part number:
50PINADP
Compatible with:
iDS2, iNS2

This adapter plugs into the 50-pin cable harness from an iCCU-S and makes the same connections via the cable A & C terminal location on iCCU-S2, allowing for a quick swap out of an iCCU-S to an iCCU-S2 without having to redo any of the wiring (if using just cables 2 & 4).

Download the cutsheet

iCCU-S2 any cabinet cable package

Part number:
ACCP
Compatible with:
iDS2, iNS2 

This cable package supplies you with the cables and interconnect board needed to install an iCCU-S2 controller in any style cabinet. This style of installation requires each cable wire to be terminated to a screw terminal location in the cabinet.

Download the cutsheet

iCCU-S2 to ped head load switch connector cable

Part number:
CABLE-A
Compatible with:
iDS2, iNS2

This nine-wire cable connects the iCCU-S2 to the ped head load switches in a traffic cabinet to receive ped interval timing.

Download the cutsheet

iCCU-S2 to EV/PR connector cable

Part number:
CABLE-B
Compatible with:
iDS2, iNS2

This six-wire cable connects the iCCU-S2 to the emergency vehicle preemption (EV/PR) inputs in a traffic cabinet.

Download the cutsheet

iCCU-S2 to logic ground connector cable

Part number:
CABLE-C
Compatible with:
iDS2, iNS2

This six-wire cable connects the iCCU-S2 to the ped inputs and logic ground in a traffic cabinet to place ped calls to the controller.

Download the cutsheet

iCCU-S2 general purpose input cable

Part number:
CABLE-D
Compatible with:
iDS2, iNS2

This four-wire cable connects to the iCCU-S2 and allows general purpose (GP) inputs to be received by connecting to outputs from the traffic cabinet controller.

Download the cutsheet

iCCU-S2 PLC to iN2-ICB connector cable

Part number:
BTN-PLC-CABLE
Compatible with:
iDS2, iNS2 

This two-wire cable supplies power and data to the iNS buttons in the field. Connects iCCU-S2 button PLC to the iN2-ICB interconnect board.

Download the cutsheet

Standard SDLC cable

Part number:
iN2-SDLC-CABLE
Compatible with:
iDS2, iNS2

This is a standard 6 foot SDLC cable for the iCCU-S2.

Download the cutsheet

SDLC “Y” cable

Part number:
iN2-SDLC-YCABLE
Compatible with:
iDS2, iNS2

This is a custom SDLC cable for use when there are no available SDLC connection points in an intersection traffic cabinet, to allows the iCCU to tap into an existing SDLC connection.

C4 cable harness

Part number:
iN2-C4-CABLE-C
Compatible with:
iDS2, iNS2

This cable is used to interface the iCCU-C2 to a 300 series traffic cabinet.

Download the cutsheet

3-wire cable

Part numbers:
12 ft: iN3-CABLE-12
24 ft: iN3-CABLE-25
50 ft: iN3-CABLE-50
Compatible with:
iDS3, iNS3, iDS2, iNS2

This cable connects the iPHCU3S to the iNS3 or iNS2 in 3-wire mode. Comes in 12, 25 and 50 foot lengths.

Extended mount, 6 or 12 in

Part numbers:
iNS-EXT-06, iNS-EXT-12
Compatible with:
iDS2, iDS3, iNS2, iNS3, iNX, iN2, iN3, PBF2, PBF2C

This extended mount is designed to mount an APS, AID, or Bulldog frame either 6 or 12 in from a traffic pole, to extend the unit closer to the crosswalk. Black, yellow, or galvanized finish.

Download the cutsheet

Angled extended mount, 6 or 12 in

Part numbers:
iNS-EXTANG-06, iNS-EXTANG-12
Compatible with:
iDS2, iDS3, iNS2, iNS3, iNX, iN2, iN3, PBF2, PBF2C

This angled extended mount reduces button height up to 5 in. Extends either 6 or 12 in from the pole. Galvanized finish.

Download the cutsheet

Height-reducing extended mount

Part number:
iNS-EXTHTRED
Compatible with:
iDS2, iDS3, iNS2, iNS3, iNX, iN2, iN3, PBF2, PBF2C

This extended mount is curved down and reduces button height up to 15 in. Galvanized finish.

Download the cutsheet

Conduit mount

Part number:
PBSCM
Compatible with:
iDS2, iDS3, iNS2, iNS3, iNX, iN2, iN3

This mount is designed for mounting an APS or AID to a wooden, concrete, or metal surface that does not allow internal wire routing to the button. A ½ in diameter conduit connects to the bottom of the mount. Black finish only.

Download the cutsheet

Fluted mounting adapter

Part number:
iNSPA-B-FP
Compatible with:
iDS2, iDS3, iNS2, iNS3, iNX, iN2, iN3, PBF2, PBF2C

This adapter is designed to allow an APS, AID, or Bulldog frame to be mounted directly on, or up to 20 degrees to either side of a flute. Black finish only.

Download the cutsheet

Dual adapter for 2.9 in OD pole

Part number:
iNSDM-2.9-B
Compatible with:
iDS2, iDS3, iNS2, iNS3, iNX

This adapter is for mounting two APS on a 2.9 in OD pole so that they can use 9×12 or 9×15 signs and not touch. Black finish only.

Download the cutsheet

90 degree adapter

Part number:
iNS-90DEGADPTR
Compatible with:
iDS2, iDS3, iNS2, iNS3, iNX, iN2, iN3, PBF2, PBF2C

This adapter designed to mount APS & Bulldog frames to either the right or the left of a mounting extender. Can reduce/adjust button mounting height up to 15 in. Black finish only.

Download the cutsheet

CCU-BRKT mount

Part number:
CCU-BRKT
Compatible with:
CCU2EN, iCCU-S, iCCU-S2

This mount is designed to hold a control unit and bolt to a rack channel with EIA universal spacing.

Download the cutsheet

Push button frame with built in cup

Part number:
PBF2C
Compatible with:
BDL3, BDSP

The PBF2C is designed to mount a Polara Bulldog push button with a sign, and to protect the wires and terminal block. Fits 5×7, 9×12 or 9×15 signs. Yellow, green, or black finish.

Download the cutsheet

Low-profile push button frame

Part number:
PBF2
Compatible with:
BDL3, BDSP

This push button frame is designed for mounting a Bulldog with the lowest profile possible so that the button is less likely to be used as a foot hold for climbing the pole. Fits 5×7, 9×12 or 9×15 signs. Black finish only.

Download the cutsheet

Universal Bulldog pole mount

Part number:
BDPM3
Compatible with:
BDL3, BDSP

Low profile Bulldog mount, works as an adapter to existing third-party button mounting cups. Yellow, green, or black finish.

Download the cutsheet

Push button adapter plate

Part number:
PBAP9X12-PC
Compatible with:
BDL3, BDSP

Allows Bulldog mounting to third-party cast 9×12 in push button frames with a molded bezel for a 2 in ADA button. Yellow, green, or black finish.

Download the cutsheet

Dual PBS adapter 

Part number:
PBF2S
Compatible with:
PBF2, PBF2C

This adapter is for mounting two push button frames on a pole so that they can use 9×12 or 9×15 signs without contact. Available for 2.9 or 4.5 in OD poles. Black finish only.

Download the cutsheet

9×12 sign backplate

Part number:
PBFA9X12
Compatible with:
iDS2, iDS3, iNS2, iNS3, iN2, iN3, PBF2C, PBF2

This sign backplate attaches to an APS or push button frame for mounting a 9×12 crosswalk sign. Yellow, green, or black finish.

Download the cutsheet

9×15 sign backplate

Part number:
PBFA9X15
Compatible with:
iDS2, iDS3, iNS2, iNS3, iN2, iN3, PBF2C, PBF2

This sign backplate attaches to an APS or push button frame for mounting a 9×15 crosswalk sign. Yellow, green, or black finish.

Download the cutsheet

Polara PC app dongle

Part number:
iN-DGL
Compatible with:
iDS2, iDS3, iNS2, iNS3, iN2, iN3

This dongle allows a computer with Polara’s free Intelligent Configurator app to communicate with an iNS APS or an iCCU. Your computer must have Windows 7 or higher.

Download the cutsheet

iNS set up box

Part number:
iNS-SUB
Compatible with:
iDS2, iDS3, iNS2, iNS3, iN2, iN3

Powers APS in 3-wire mode so they can be set up or programmed in the shop without being connected to a traffic cabinet or signal head.
Part number: iNS-SUB

Download the cutsheet

R/L arrow button assembly

Part number:
850-491-1
Compatible with:
iDS2, iDS3, iNS2, iNS3, iNX, iN2, iN3

Field-replaceable single-direction arrow button assembly.

Bi-directional arrow button assembly

Part number:
850-491-2
Compatible with:
iDS2, iDS3, iNS2, iNS3, iNX, iN2, iN3

Field-replaceable bi-directional arrow button assembly.

Plain button assembly

Part number:
850-491-1
Compatible with:
iDS2, iDS3, iNS2, iNS3, iNX, iN2, iN3

Field-replaceable button assembly with no arrow.

iNX color change kit

Part number:
iNX-CCK
Compatible with:
iNX

This color change kit is a bundle of the required parts needed to change the front cover color on an iNX.

Download the cutsheet

iNS external speaker

Part number:
2WEXTSPKR
Compatible with:
iDS2, iDS3, iNS2, iNS3

External horn-style speaker that installs on the signal head for audible APS beaconing on long or skewed crossings. Requires an iNS ordered with the -ES option.

iNS field-installable replacement speaker

Part number:
iNS-SPKR
Compatible with:
iDS2, iDS3, iNS2, iNS3, iNX

This speaker is set up to allow easy field replacement of an APS speaker.

Download the cutsheet

Polara matching color paint

Part numbers:
190-1054 (black), 190-1055 (green), 190-1056 (yellow)

Cans of spray paint in the colors that match Polara’s black, green and yellow powder coat colors.