RF Control 2.7.2 - App Store

---

About RF Control

RF Control remotely controls up to 48 channels of Sennheiser* and Shure* wireless receivers in one application, side-by-side. The intuitive user interface provides a quick overview of the most vital parameters of your...

RF Control remotely controls up to 48 channels of Sennheiser* and Shure* wireless receivers in one application, side-by-side. The intuitive user interface provides a quick overview of the most vital parameters of your wireless receivers. Dedicated screens have been carefully developed to give you control to parameters that are relevant in a live situation while securing access to the ones that might be harmful to the safety of the system. Following devices are supported by utilizing the manufacturers remote control protocols: Sennheiser: EW-DX, EM 3732*, 2000* series and evolution G3 and G4* wireless receivers. Sennheiser: EM 6000 receivers Shure: ULX-D* Depending on the manufacturer of the receiver RF Control supports monitoring of the most relevant parameters including: - RF level bargraph (all) - AF Level bargraph (all) - Battery status information (all) - Remaining battery time (Shure, EM6000, EW-DX (with Li-Ion battery)) - Device name (all) - EQ type (2000 and ewG3) - Command settings (EM3732COM) - AF Out level (all) - Squelch level (Sennheiser) - Mic Offset (Shure, EM6000, EW-DX) - Lock Status (Shure, EM6000, EWDX) - Encryption Status (Shure, EM6000, EW-DX) - TX Type (Shure, EM 6000, EW-DX) - TX RF Power (Shure) - LQI (EM6000, EW-DX) - Capsule type (EM6000, EW-DX) - Warning indicators (Sennheiser: Low Bat, RX Mute, TX Mute, RF Mute, AF Peak, NoLink, Encryption mismatch) (Shure: Low Bat, Interference, RX Mute, TX Mute, Enrcryption mismatch, AF Peak) A plot of the RF and AF levels is displayed over time, making it the perfect companion for walk tests and spotting dropouts in your audio. The full screen plot window of the iPad version allows to scroll through the recorded RF and audio levels to look up for problems and drop-outs even after hours of recording. All relevant parameters can be remotely controlled: - Frequency, bank, channel (all) - Device name (all) - EQ type (2000 and ewG3) - Command type (EM3732COM) - AF Out level (all) - Squelch level (Sennheiser) - RX Mute (Shure) iPad only: The scan window allows you to use one of the recognized Sennheiser devices to scan the RF environment. The frequency plot can be used to drill down the spectrum and look for free frequencies. The RF Inspector allows for sample accurate readout of the scan data at your fingertips. The scan data can be stored as *.csv file and sent as attachment via email. The *.csv file I can be loaded from third party software for frequency coordination and planning. Scan is not supported by Shure devices. During start up RF Control will scan your network for connected devices. For Sennheiser 2000 series and evolution wireless G3 devices Firmware 1.7.0 or higher needs to be present on the receivers to support the remote control protocol. The app can monitor up to 48 channels in mixed configurations. The device list allows access to all devices in the network and selection of 48 devices for monitoring. The order of channels can be freely arranged and will be restored at the next start of the app. Notes: RF Control is the new name of the wilSmoTe app. RF Control does not support IEM transmitters! Channel count depends on hardware performance! Sennheiser, EW-DX, EM 6000, EM 3732, 2000 series, evolution G3 / G4 are brands, products or trademarks of Sennheiser electronic GmbH & Co.KG and not associated in any way with RF Control. Shure, ULXD, QLXD, Axient are brands, products or trademarks of Shure Inc. and not associated in any way with RF Control.

Version History Fix an issue with the detection of Sennheiser G3 und EM20x0 devices. 2.7.2 12/01/2025 Fixed a problem with false detection of Shure devices 2.7.1 09/03/2025 Support for Sennheisers EWDX4 and EWDXD four channel receivers. Fixes for issues with Shure ULXD and continuous improvements for stability. 2.7.0 10/16/2024 This version contains overall improvements. Also it fixes problems with Sennheiser's EM3732COM and Shure's QLX-D receivers. 2.6.1 08/25/2024 Added support for Sennheiser's EW-DX dual channel digital wireless receivers. Integrated all in-app purchases into this version as a complete package. Extended the monitoring for up to 48 channels. Removed Dropbox support for scan files. 2.6.0 07/25/2023 Fix issue with detection of Sennheiser devices 2.5.5 09/13/2022 In some cases the cycle scan would not cycle but just stop after first run on ewG4 and EM 6000 2.5.4 06/12/2019 This version fixes a problem when opening the settings page for ew G4 receivers. Sometimes the app didn't work properly when multiple EM 6000 receivers where connected and the receivers did not show up in the scan dialog. 2.5.3 05/05/2019 We found an issue with Sennheiser ewG3 devices running firmware 1.8.0 not showing metering data and a crash when opening the settings window. 2.5.1 01/24/2019 New name and new devices - RF Control (formerly wilSmoTe) now supports also Sennheiser ewG4 EM300-500 receivers as well as EM6000 series receivers. Also there have been improvements and fixes for the previous version including support for the bigger iPhone Screens and the changed Dropbox API. While it's most convenient to use the app via WiFi connection it also supports common LAN adapters for iPhone and iPad. 2.5 12/29/2018 Version 2.2.3 - fixed issues with Shure devices running FW 1.4.8 and higher - performance improvements Version 2.2 This exciting release adds support for Shure Axient, ULX-D and QLX-D wireless receivers. Now you can control receivers from Sennheiser and Shure in one application, side-by-side. Due to the increased performance of the current and next iPad and iPhone processors the channel count has been increased to 24. For legacy devices you can stick with 16 channels to prevent your CPU from maxing out. And finally there are the fixes and improvements under the hood, 64 bit support, IOS 9 compatibility. IOS 7 is no longer supported - sorry if you still love your iPhone 4. 2.2.3 11/25/2015 Version 2.2 This exciting release adds support for Shure Axient, ULX-D and QLX-D wireless receivers. Now you can control receivers from Sennheiser and Shure in one application, side-by-side. Due to the increased performance of the current and next iPad and iPhone processors the channel count has been increased to 24. For legacy devices you can stick with 16 channels to prevent your CPU from maxing out. And finally there are the fixes and improvements under the hood, 64 bit support, IOS 9 compatibility. IOS 7 is no longer supported - sorry if you still love your iPhone 4. 2.2.2 10/22/2015 This exciting release adds support for Shure Axient, ULX-D and QLX-D wireless receivers. Now you can control receivers from Sennheiser and Shure in one application, side-by-side. Due to the increased performance of the current and next iPad and iPhone processors the channel count has been increased to 24. For legacy devices you can stick with 16 channels to prevent your CPU from maxing out. And finally there are the fixes and improvements under the hood, 64 bit support, IOS 9 compatibility. IOS 7 is no longer supported - sorry if you still love your iPhone 4. 2.2 10/16/2015 iPad only: RF spectrum scan window to use with EM 3732, ewG3 or 2000 series receivers Zoom-able frequency plot iPad only: New ScanPacks for RF scan (in-App purchase): Scan with any device connected to the app Single shot or continuous cycle scan RF Inspector for easy drill down Export of scan data as *.csv file (compatible with WSM) Upload the *.csv file to your personal Dropbox Send the *.csv file via email Package 1) Metro ScanPack for ewG3 and 2000 series Package 2) EM37 ScanPack for EM 3731 / EM3732 all platforms: Fixed issue with device firmware 1.7.7 General improvements Please take a minute to rate this app. It helps a lot to keep up motivation for new features. 2.1 03/05/2015 Support for EM 3731, EM 3732 including Command versions UI improvements for better visualization Color coding per device family Device list shows all compatible devices in the network Up to 16 channels from the device list can be selected for monitoring General improvements 2.0 08/03/2014 New features - Support for 16 channels of RF - Panel sorting - Restore of previous panel arrangement Improvements - Improved accuracy for meters and level recorders - Panel numbering for better navigation - minor fixes 1.3 03/08/2014 - fixed problems with EM300 1.2.1 12/13/2013 Fullsize plot of RF levels and AF levels on iPad. Pan through your data and check for low levels during walk tests. IOS 7 look and feel for buttons New logo Improved graphics Bug fixes 1.2 12/04/2013 fixed occasional graphic issues on iPhone 4 - metering - plotwindow - ghost icon 1.1.1 09/27/2013 iPad support included - 4 channels side by side, monitors max 8 channels simultaneously iPhone version now monitorss 8 channels in parallel Bugfixes 1.1 09/14/2013 1.0 06/28/2013

---

Previous Versions

Here you can find the changelog of RF Control since it was posted on our website on 2023-09-25 11:09:52. The latest version is 2.7.2 and it was updated on 2026-06-23 23:27:08. See below the changes in each version.

---

Related Apps

Here you can find apps that are similar with RF Control.

---

Disclaimer