I have had my Netdisk system for years, (had it replaced once before) and I have always loved it.
Lately I have been having connectivity issues. I'm running NDAS 3.72.2070.1456 SVN Private version of software. Quite often I try to access the drive, and find it is unmounted. Or I will be accessing something on the drive, and the program will lock up, and I eventually get an access message and the NDAS management program will say the device is unmounted.
I can almost always remount it right away, but occasionally I have to power cycle it before I can get access.
I don't see a new version of software, any thoughts on what is going on? Onboard network issues? I don't think its the drive itself, but I guess it could be.
As I said, I have always loved the device, and would love to keep using it for years to come, so any ideas would be greatly appreciated.
Thanks!
Svar fra
Stephen Prastman
The problem with mounting/unmounting could also be caused by the disk itself and the controller. Usually, an issue like this indicates there is a problem with the drive itself, the controller of the drive or the cable. The only thing you can change is the cable, therefore start with that to eliminate the possibility.
If the disk is having issues, then you'll have to take it to service repair, but that is a problem as well since you can't enjoy official support. I've just checked and the website is displaying a page encountered when the domain expired.
Is there an updated NDAS driver that works with Windows 10?
R
Svar fra
Robert Polubinski
No, the software/driver is not compatible with Windows 10. Based on the information found on the developer's website, you can install the driver and application on 32&64 bit Windows 2000, XP, Vista, 2008, and Windows 7.
Note: In Windows 10, restart the computer without Driver Enforcement, connect the drive, and then install the software. Use the manual way to point the driver installation window to where the software is installed.
I used the NDAS with XP and Windows 8 without any problems. I recently upgraded to Windows 8.1 and on a separate partition to Windows 10 TP 10074.
It looks as if everything was OK, code accepted, but clicking on VERBINDEN (German for connect) nothing happens.
S
Svar fra
Sean Hill
The software doesn't appear to be compatible with the operating systems you're using. According to the official website, the software supports Windows 7 as the latest version of Windows supported. However, in Windows 8.1 or Windows 10, right click the file and select Troubleshoot Compatibility and then follow the recommendations. Run the software as Administrator as well and then try to connect.
I have had my Netdisk system for years, (had it replaced once before) and I have always loved it.
Lately I have been having connectivity issues. I'm running NDAS 3.72.2070.1456 SVN Private version of software. Quite often I try to access the drive, and find it is unmounted. Or I will be accessing something on the drive, and the program will lock up, and I eventually get an access message and the NDAS management program will say the device is unmounted.
I can almost always remount it right away, but occasionally I have to power cycle it before I can get access.
I don't see a new version of software, any thoughts on what is going on? Onboard network issues? I don't think its the drive itself, but I guess it could be.
As I said, I have always loved the device, and would love to keep using it for years to come, so any ideas would be greatly appreciated.
Thanks!
The problem with mounting/unmounting could also be caused by the disk itself and the controller. Usually, an issue like this indicates there is a problem with the drive itself, the controller of the drive or the cable. The only thing you can change is the cable, therefore start with that to eliminate the possibility.
If the disk is having issues, then you'll have to take it to service repair, but that is a problem as well since you can't enjoy official support. I've just checked and the website is displaying a page encountered when the domain expired.
Is there an updated NDAS driver that works with Windows 10?
No, the software/driver is not compatible with Windows 10. Based on the information found on the developer's website, you can install the driver and application on 32&64 bit Windows 2000, XP, Vista, 2008, and Windows 7.
Official website: http://ximeta.com/
Note: In Windows 10, restart the computer without Driver Enforcement, connect the drive, and then install the software. Use the manual way to point the driver installation window to where the software is installed.
I used the NDAS with XP and Windows 8 without any problems. I recently upgraded to Windows 8.1 and on a separate partition to Windows 10 TP 10074.
It looks as if everything was OK, code accepted, but clicking on VERBINDEN (German for connect) nothing happens.
The software doesn't appear to be compatible with the operating systems you're using. According to the official website, the software supports Windows 7 as the latest version of Windows supported. However, in Windows 8.1 or Windows 10, right click the file and select Troubleshoot Compatibility and then follow the recommendations. Run the software as Administrator as well and then try to connect.