New Voacap
21 August, 2011Santina de Covadonga 2011 Award in ROS
15 August, 2011ROS with balcony antenna
15 August, 2011This antenna is used by EA5GTU/P during his holidays in La Manga (Spain). Besides of this antenna being low efficient on HF, he could contact with YV5MM (Venezuela) with ROS.
And this is an example of how you should not configure your Rig filter. In this case ROS frequencies below 1000Hz are lost in a Icom-7000. However the contact with YV5MM could be completed in the worst conditions.
First on air test of the ROS Digital Repeater Mode
3 August, 2011First on air test of the ROS Digital Repeater Mode (by Graham G0NBD)
EA5HVK <> IK2AOS <> G0NBD
Communication where established on 28.295 Mhz , all stations using the same frequency
The RF path G0NBD <> IK2AOS and EA5HVK <> IK2AOS ,
No signal from EA5HVK could be observed at IO83LK
Later , the cross band function was successfully trailed, with a HF / VHF two way qso between G4WGT and EA5HVK using my station G0NBD as the cross band repeating station.
G4WGT using 144.980 and EA5HVK 10.134.
The RF path G4WGT <> G0NBD <> EA5HVK
Selective decoding
1 August, 2011From 3 August 2011, the new ROS Mode accepts selective decoding and it will not be compatible with the present ROS Mode.
In position ALL decode any message (recommended for SWL operation).
In position RN6AM only decode RN6AM transmissions (recommended for QSO operation).

EA1HBX 6M Beacon
17 July, 2011ROS 6m QRP Beacon active in Ourense
(Frequency: 50295 USB
Power: 5 w.
Antenna: Multipole military field antenna
Locator: IN62bl
Sofware: ROS v6.5.8. Beta
Interval: Every 5 minutes
More info: http://www.qrz.com/callsign/EA1HBX
ED1YBL UHF Beacon
3 July, 2011ROS UHF Beacon active in Ourense (Meda Mountain)
Frequency: 432.097 USB
Power: 5 w.
Antenna: Vertical
Locator: IN62EI
Altitude: 1.325 m.
Sofware: ROS v6.5.6. Beta
Interval: Every 5 minutes
More info: http://www.ea1uro.com/balizas.html
ROS with SoftRock SDR
28 June, 2011Now ROS can operate directly with some SDR kits, like SoftRock, KTH, PM, Zeta SDR, G4JNT LF Upconverter…. (ask me for inlude new SDR kits)
In Rig Menu, click on SDR if you are using some of these kits. I/Q processing will be activated automatically. You need to have Stereo input or output (Usually, Mic input is mono).
Adjust the I/Q balance using the Phase, Gain and Delay sliders. Configuration is stored for each band. Click on Fine for a Fine Adjust.
If the SDR if shifted in frequency you can use the Offset Slider for a Fine Frequency Adjust too.
For Zeta SDR you have to to enter the LO frequency. 14.318/4 is ideal for using ROS on 80 meters band.
The G4JNT LF UpConverter was tested by his author, Andy Talbot, using the Soundmax Internal Soundcard getting 60dB of image rejection for the ROS MF Mode (137 and 500 Khz USB)
For monitoring the I/Q audio proccessed while you are decoding, click on Monitor. The Monitor audio filter is 300-2700 Hz.
Specials thanks to Dave 2E0DPQ for a lot of test with softRock between England and Spain. He got a complete communication with Argentina on 20 meters with 1 watt and ROS.
Also special thanks to KB9YIG for the Softrock TX/RX kit, and PE0FKO, PA0RWE and IW3AUT for the Si570 support, and G4JNT for the TX I/Q adjustement test.




















You must be logged in to post a comment.