Fixes #5941.

Not entirely sure that this will fix the problem (couldn't reproduce), but in any case this is an artifact of a hack in the P2P transport refactor to make it work with the legacy P2P stack, and will be removed when the refactor is done anyway.

Co-authored-by: Emmanuel T Odeke <emmanuel@orijtech.com>

Closes #5907

- add init-corpus to blockchain reactor
- remove validator-set FromBytes test
now that we have proto, we don't need to test it! bye amino
- simplify mempool test
do we want to test remote ABCI app?
- do not recreate mux on every crash in jsonrpc test
- update p2p pex reactor test
- remove p2p/listener test
the API has changed + I did not understand what it's tested anyway
- update secretconnection test
- add readme and makefile
- list inputs in readme
- add nightly workflow
- remove blockchain fuzz test
EncodeMsg / DecodeMsg no longer exist

Co-authored-by: Marko <marbar3778@yahoo.com>

See #5936 and #5938 for background.

The plan was initially to have `DialNext()` and `EvictNext()` return a channel. However, implementing this became unnecessarily complicated and error-prone. As an example, the channel would be both consumed and populated (via method calls) by the same driving method (e.g. `Router.dialPeers()`) which could easily cause deadlocks where a method call blocked while sending on the channel that the caller itself was responsible for consuming (but couldn't since it was busy making the method call). It would also require a set of goroutines in the peer manager that would interact with the goroutines in the router in non-obvious ways, and fully populating the channel on startup could cause deadlocks with other startup tasks. Several issues like these made the solution hard to reason about.

I therefore simply made `DialNext()` and `EvictNext()` block until the next peer was available, using internal triggers to wake these methods up in a non-blocking fashion when any relevant state changes occurred. This proved much simpler to reason about, since there are no goroutines in the peer manager (except for trivial retry timers), nor any blocking channel sends, and it instead relies entirely on the existing goroutine structure of the router for concurrency. This also happens to be the same pattern used by the `Transport.Accept()` API, following Go stdlib conventions, so all router goroutines end up using a consistent pattern as well.

Closes: #5806 

Co-authored-by: Lanie Hei <heixx011@umn.edu>

## Description

add section on configuring log levels

Closes: #XXX

outputs is a property of the job, not an individual step.

## Description

Update the faux router to either drop channel errors or handle them based on an argument. This prevents deadlocks in tests where we try to send an error on the mempool channel but there is no reader.

Closes: #5956

This improves the `peerStore` prototype by e.g.:

* Using a database with Protobuf for persistence, but also keeping full peer set in memory for performance.
* Simplifying the API, by taking/returning struct copies for safety, and removing errors for in-memory operations.
* Caching the ranked peer set, as a temporary solution until a better data structure is implemented.
* Adding `PeerManagerOptions.MaxPeers` and pruning the peer store (based on rank) when it's full.
* Rewriting `PeerAddress` to be independent of `url.URL`, normalizing it and tightening semantics.

Follow-up from #5947, branched off of #5954.

This simplifies the upgrade logic by adding explicit eviction requests, which can also be useful for other use-cases (e.g. if we need to ban a peer that's misbehaving). Changes:

* Add `evict` map which queues up peers to explicitly evict.
* `upgrading` now only tracks peers that we're upgrading via dialing (`DialNext` → `Dialed`/`DialFailed`).
* `Dialed` will unmark `upgrading`, and queue `evict` if still beyond capacity.
* `Accepted` will pick a random lower-scored peer to upgrade to, if appropriate, and doesn't care about `upgrading` (the dial will fail later, since it's already connected).
* `EvictNext` will return a peer scheduled in `evict` if any, otherwise if beyond capacity just evict the lowest-scored peer.

This limits all of the `upgrading` logic to `DialNext`, `Dialed`, and `DialFailed`, making it much simplier, and it should generally do the right thing in all cases I can think of.

Adds a naïve `PeerManager.Advertise()` method that the new PEX reactor can use to fetch addresses to advertise, as well as some other `FIXME`s on address advertisement.

## Description

Fixes the data race in usage of `WaitGroup`. Specifically, the case where we invoke `Wait` _before_ the first delta `Add` call when the current waitgroup counter is zero. See https://golang.org/pkg/sync/#WaitGroup.Add.

Still not sure how this manifests itself in a test since the reactor has to be stopped virtually immediately after being started (I think?).

Regardless, this is the appropriate fix.

closes: #5968

## Description
 
- bump deadlock dep to master
  - fixes `make test` since we now use `deadlock.Once`

Closes: #XXX

and preserve exit code.

```
2021/01/26 03:34:49 workers: 2, corpus: 4 (8m28s ago), crashers: 0, restarts: 1/9976, execs: 11013732 (21596/sec), cover: 121, uptime: 8m30s
make: *** [fuzz-mempool] Terminated
Makefile:5: recipe for target 'fuzz-mempool' failed
Error: Process completed with exit code 124.
```

https://github.com/tendermint/tendermint/runs/1766661614

`continue-on-error` should make GH ignore any error codes.

This adds a prototype PEX reactor for the new P2P stack.

Fixes #5899 by renaming a bunch of P2P Protobuf entities (while maintaining wire compatibility):

* `Message` to `PexMessage` (as it's only used for PEX messages).
* `PexAddrs` to `PexResponse`.
* `PexResponse.Addrs` to `PexResponse.Addresses`.
* `NetAddress` to `PexAddress` (as it's only used by PEX).

This changes the new prototype PEX reactor to resolve peer address URLs into IP/port PEX addresses itself. Branched off of #5974.

I've spent some time thinking about address handling in the P2P stack. We currently use `PeerAddress` URLs everywhere, except for two places: when dialing a peer, and when exchanging addresses via PEX. We had two options:

1. Resolve addresses to endpoints inside `PeerManager`. This would introduce a lot of added complexity: we would have to track connection statistics per endpoint, have goroutines that asynchronously resolve and refresh these endpoints, deal with resolve scheduling before dialing (which is trickier than it sounds since it involves multiple goroutines in the peer manager and router and messes with peer rating order), handle IP address visibility issues, and so on.

2. Resolve addresses to endpoints (IP/port) only where they're used: when dialing, and in PEX. Everywhere else we use URLs.

I went with 2, because this significantly simplifies the handling of hostname resolution, and because I really think the PEX reactor should migrate to exchanging URLs instead of IP/port numbers anyway -- this allows operators to use DNS names for validators (and can easily migrate them to new IPs and/or load balance requests), and also allows different protocols (e.g. QUIC and `MemoryTransport`). Happy to discuss this.

## Description

Looks like I missed a test in the original PR when fixing the tests.

Closes: #5956

This ensures we don't leak dial goroutines when shutting down the router.