• What is RESTuino?
• Requirements
• Installation
• Usage
  • Control GPIO
  • Control of the entire system
• Examples
  • curl
  • Python
  • homebridge
  • Talend API Tester

In embedded development, we have Arduino and CircuitPython as software initiatives to improve development productivity. Today, a new standard in embedded development is born. It is the RESTuino, interactive embedded development firmware for ESP32.

I created an external API layer for the hardware abstraction layer to enable GPIO operations from outside the microcontroller. In this case, I created RESTful API for the Arduino hardware abstraction layer inside the ESP32 microcontroller to enable GPIO operations.

Specifically, you can specify a GPIO number in the URL, POST to define a pin state (digitalWrite, digitalRead, etc.), PUT to update the value (digitalWrite to HIGH, LOW, etc.), GET to get current information, DELETE to disable a pin state. And if you do save, the pin state is saved in EEPROM, so it is easy to operate as client-side software in IoT.

🌱 RESTuino makes it possible to communicate system functions & data in the IoT.

✨ RESTuino allows us to make...

• IoT client Arduino GPIOs can be manipulated via REST API.
• Interactive Microcomputer Programming via curl, Talend API Tester or similer.

✍ RESTuino can be operated with...

• curl
• Homebridge
• Python(requests)
• Talend API Tester
  or similer.

• ESP32-based board

  The tested boards are as follows. Other products can also be used if they are equipped with esp32.

  • ESP32 DevKitC
  • MH ET LIVE ESP32DevKIT

• PlatformIO or Arduino IDE

See PlatformIO example, Arduino IDE example

You can install the library in two ways.

• PlatformIO
• Arduino IDE

1. Clone this repository.

   $ git clone https://github.com/takeyamayuki/RESTuino.git

2. Open the esp32_platformio example in PlatformIO or esp32_basic example in Arduino IDE.

3. Define ssid, password of your wifi router by changing ssid_def, ssid_pass. If more than one RESTuino is to be installed, change host_name. serial_baud is the baud rate of the serial monitor. 9600 is the default value.

   restuino.host_name = "restuino";
   restuino.ssid_def = "YOUR_SSID";
   restuino.ssid_pass = "YOUR_PASSWORD";
   restuino.serial_baud = 9600;

4. Build and upload.

5. Clear EEPROM.

   Initialize the RESTuino system when you see WiFi connected. on the serial monitor.

   $ curl restuino.local/ -X DELETE  
   Change all pins to nan status...  

6. Use this the way you want to use it.

1. Specify the GPIO number in the URL
2. POST to define the pin status (digitalWrite, digitalRead, etc.)
3. PUT to update the value (HIGH for digitalWrite, etc.)
4. GET to obtain current information (digitalRead, etc.)
5. DELETE to disable the pin status

Note
When sending the request body, always specify Content-Type: text/plain as the header.

http://restuino.local/gpio(pin_number)

(pin_number) is the pin number of the GPIO. For example, http://restuino.local/gpio15 is the GPIO15 of ESP32.
It is recommended to use http://restuino.local instead of accessing the IP address, because of the heavy use of ESP.restart() in the RESTuino process.

Specify the target GPIO pin by URL.

Use POST to set the status of a pin.

Request body: digitalRead | digitalWrite | analogRead | ledcWrite | Servo | (touch) | (dacWrite)

# e.g. digitalWrite
$ curl restuino.local/gpio15 -X POST -H 'Content-Type: text/plain' -d 'digitalWrite'
digitalWrite

Use PUT to change or define the output value of any pin.
The following request body can be sent when the GPIO pin set by POST is in the following state.

• digitalWrite

  Request body: HIGH | LOW | 0 | 1

  # e.g.
  $ curl restuino.local/gpio15 -X PUT -H 'Content-Type: text/plain' -d 'LOW'
  LOW

• ledcWrite (alternative to analogWrite in esp32)

  Request body: 0~256 numbers

  # e.g.
  $ curl restuino.local/gpio15 -X PUT -H 'Content-Type: text/plain' -d '100'
  100

• Servo
  Request body: 0~180 numbers | switch

  • 0~180 numbers: a servo motor moves to the angle specified by value.
  • switch: Each time the following command is sent, the servo motor moves back and forth between angle and angle0.

  # e.g.
  $ curl restuino.local/gpio15 -X PUT -H 'Content-Type: text/plain' -d '88'
  88

Use GET to get the status of any pin.
The following response body is received when the pin set by POST is in the following state.

• analogRead: 0~4095 numbers
• digitalRead: 0 | 1
• Servo: 0~180 numbers

# e.g. digitalRead
$ curl restuino.local/gpio1 -X GET
0

Use DELETE to disable any pin (actually, save the setting in EEPROM and restart).

# e.g.
$ curl restuino.local/gpio1 -X DELETE
Change the pin to nan status... 

• http://(IP_address)
  The IP address can be obtained via serial communication or http://restuino.local via GET method (It's easy with a browser).
  It is recommended to use http://restuino.local instead of accessing the IP address, because of the heavy use of ESP.restart() in the RESTuino process.

• http://restuino.local

Request body: save | load | reboot

• save: Save the current GPIO setting status to EEPROM.
• load: Load GPIO settings stored in EEPROM and reflect to actual pin settings.
• reboot: Reboot ESP32.

Note
The load is done automatically at startup, but the user must save before turning off the power.
When operating as an IoT client, once the pin state is saved, it will be saved in eeprom, so there is no need to save after that.

# e.g.
$ curl restuino.local/ -X POST -H 'Content-Type: text/plain' -d 'save'
Wrote

Obtain IP address and GPIO status. GPIO status is output in chunks of 40. Starting from the first left digit, GPIO0, 1,2.... and its value is defined as follows.

$ curl restuino.local/ -X GET
{
  "IP address": "192.168.0.29",
  "GPIO status": "2000000050000002200000000000000000000000"
}

e.g.
Looking at the first digit of GPIO status(GPIO0), there is a number 2, which means digitalwrite. Therefore, pinMode(0,OUTPUT) is executed internally so that GPIO0 becomes digitalwrite.

Disable all pins (actually, save the setting in EEPROM and restart).

$ curl restuino.local/ -X DELETE
Change all pins to nan status...

Not defined.

See examples.

• python-L-chika : Programs to turn on/off the LED connected to GPIO15 every second.

• python-Servo-switch : Programs to move the servo (connected to GPIO15) to the angle defined by angle, angle0 every second.

1. Run setup.py

   $ python setup.py

   Configure GPIO settings. Run it only once.

2. Run main.py

   $ python main.py

   This is the main program. Use only this program when incorporating it.

The program is here.

• curl-digitalRead: Scripts that executes digitalRead to GPIO15 and obtains its status.

• curl-Servo: Programs to move the servo (connected to GPIO15) to 88°.

1. Run setup.sh

   $ chmod +x setup.sh
   $ ./setup.sh

   Configure GPIO settings. Run it only once.

2. Run main.sh

   $ chmod +x main.sh
   $ ./main.sh

   This is the main program. Use only this program when incorporating it.

The program is here.

homebridge is a lightweight NodeJS server you can run on your home network that emulates the iOS HomeKit API. This allows you to use iOS apps to control devices that do not natively support HomeKit.

In the homebridge config editor, add the following to the accessories section:

"accessories": [
    {
        "accessory": "CMD",
        "name": "light",
        "on_cmd": "curl restuino.local/gpio15 -X PUT -H 'Content-Type: text/plain' -d '56'",
        "off_cmd": "curl restuino.local/gpio15 -X PUT -H 'Content-Type: text/plain' -d '6'"
    }
]