Report preparation

• I used the AI-assisted bug report tool (Help → Support → File an Issue)
• I have attached a support bundle or log file

What happened?

Hello all,

it seems that AetherSDR does not have the Hamlib emulation complete, at rigctld there is an option to send CW messages with the 'b' character, like it says here:

However, when software sends that 'b' character answer of AetherSDR is this one:

[16:13:41.059] DBG: rigctld cmd: "|f" -> resp: "get_freq:|Frequency: 14023224|RPRT 0"
[16:13:41.178] DBG: rigctld cmd: "b" -> resp: "RPRT -1"
[16:13:41.289] DBG: rigctld cmd: "|f" -> resp: "get_freq:|Frequency: 14023224|RPRT 0"

If you see AetherSDR answers with a "RPRT -1".

May you correct it please ?

Maybe better would be to implement everything from list:

Commands (some may not be available for this rig):
F: set_freq (Frequency) f: get_freq ()
M: set_mode (Mode,Passband) m: get_mode ()
I: set_split_freq (TX Frequency) i: get_split_freq ()
X: set_split_mode (TX Mode,TX Passband) x: get_split_mode ()
K: set_split_freq_mode(TX Frequency,TX Mode,TX Passband) k: get_split_freq_mode()
S: set_split_vfo (Split,TX VFO) s: get_split_vfo ()
N: set_ts (Tuning Step) n: get_ts ()
L: set_level (Level,Level Value) l: get_level (Level)
U: set_func (Func,Func Status) u: get_func (Func)
P: set_parm (Parm,Parm Value) p: get_parm (Parm)
G: vfo_op (Mem/VFO Op) g: scan (Scan Fct,Scan Channel)
A: set_trn (Transceive) a: get_trn ()
R: set_rptr_shift (Rptr Shift) r: get_rptr_shift ()
O: set_rptr_offs (Rptr Offset) o: get_rptr_offs ()
C: set_ctcss_tone (CTCSS Tone) c: get_ctcss_tone ()
D: set_dcs_code (DCS Code) d: get_dcs_code ()
?: set_ctcss_sql (CTCSS Sql) ?: get_ctcss_sql ()
?: set_dcs_sql (DCS Sql) ?: get_dcs_sql ()
V: set_vfo (VFO) v: get_vfo ()
T: set_ptt (PTT) t: get_ptt ()
E: set_mem (Memory#) e: get_mem ()
H: set_channel (Channel) h: get_channel (Channel,Read Only)
B: set_bank (Bank) _: get_info ()
J: set_rit (RIT) j: get_rit ()
Z: set_xit (XIT) z: get_xit ()
Y: set_ant (Antenna,Option) y: get_ant (AntCurr)
?: set_powerstat (Power Status) ?: get_powerstat ()
?: send_dtmf (Digits) ?: recv_dtmf ()
*: reset (Reset) w: send_cmd (Cmd)
W: send_cmd_rx (Cmd,Reply) b: send_morse (Morse)
?: stop_morse () ?: wait_morse ()
?: send_voice_mem (Voice Mem#) ?: stop_voice_mem ()
?: get_dcd () ?: set_twiddle (Timeout (secs))
?: get_twiddle () ?: uplink (1=Sub, 2=Main)
?: set_cache (Timeout (msecs)) ?: get_cache ()
2: power2mW (Power [0.0..1.0],Frequency,Mode) 4: mW2power (Pwr mW,Freq,Mode)
1: dump_caps () 3: dump_conf ()
?: dump_state () ?: chk_vfo ()
?: set_vfo_opt (Status) ?: get_vfo_info (VFO)
?: get_rig_info () ?: get_vfo_list ()
?: get_modes () ?: get_clock ()
?: set_clock (local or utc or YYYY-MM-DDTHH:MM:SS.sss+ZZ or YYYY-MM-DDTHH:MM+ZZ) ?: halt ()
?: pause (Seconds) ?: password (Password)
?: get_mode_bandwidths(Mode) ?: set_separator (Separator)
?: get_separator () ?: set_lock_mode (Locked)
?: get_lock_mode () ?: send_raw (Terminator,Command)
?: client_version (Version) ?: get_vfo_list ()
?: test (routine) ?: hamlib_version ()
?: get_gpio (GPIO#) ?: set_gpio (GPIO#,0/1)
?: set_conf (Token,Token Value) ?: get_conf (Token)

Best 73 es tks.

CT1DRB/OK8RB
David Quental

What did you expect?

I would be expected to be send well.

Steps to reproduce

1. Connect radio
2. Start AetherSDR
3. Start Not1mm software
4. Hit F1 to call
5. Radio does not send CW memory

AetherSDR version

0.9.1

Radio model & firmware

FLEX-6600 V4.1.5.39794

Operating system

macOS

OS version and hardware

It happens with any OS.